Outlets / Switches for Brentwood homes
Brentwood is large-lot estate territory with mid-century moderns, traditional homes, and contemporary builds. Many homes have whole-home Lutron RadioRA 3 or HomeWorks QSX systems, dedicated EV charger outlets in the garage (NEMA 14-50, 240V/50A), and smart-home integration that reaches every room. The work in Brentwood is rarely a single device swap — it is multi-circuit estate visits, EV charger outlet adds, and integration of new fixtures into existing premium control systems. Estates built after 2000 have modern copper, dedicated neutrals at every box, and clean grounds; older estates may have partial CO/ALR work from 1970s and 1980s rewires.
Pricing for premium device swap runs $160–260 per switch including system coordination. NEMA 14-50 EV charger outlet add (240V/50A circuit from panel to garage) requires a licensed electrician for the new circuit but handyman scope can install the receptacle and cover plate after the circuit is in place — typically $180–280 for the receptacle install alone. Whole-home Caseta or RA3 retrofit on a 5-bedroom estate runs $3,500–7,500 including hub or processor. Multi-fixture estate visits with cable concealment, finish-matched cover plates, and scene programming run $1,500–3,500 in a single visit window. Mention existing smart-home system and estate scope when you book.
About outlets / switches
Outlet and switch installation is the work of replacing, upgrading, or adding the small electrical devices behind every cover plate in your home — the receptacles you plug things into, the toggles and dimmers that control your lights, and the smart controls that connect them to apps. The job sounds trivial because each device is cheap and small, but the wiring inside the box is doing serious work: pushing 15 or 20 amps of 120-volt current through copper conductors, terminating onto small screw lugs that have to be tight, and protecting your home from the most common cause of residential fires — overheated electrical connections. A clean install means devices that work for 30 years; a sloppy install means a connection that arcs, melts the receptacle face, and starts a fire inside the wall.
Read the full Outlets / Switches guide →Pricing in Brentwood
$80–220 typical range for Brentwood jobs.
Standard outlet replacement in Los Angeles runs $80–130 for the labor on a single device, and standard switch replacement is in the same range. This assumes a like-for-like swap on a copper-wired box where the existing device comes out cleanly and the new one goes back in without surprises. Most pros price the first device higher and additional devices on the same visit lower — so two outlets in the same room is usually $130–180 total, not 2x $130. Ask for a multi-device quote if you have a list.
Brentwood outlets / switches FAQ
Can the pro install my NEMA 14-50 EV charger outlet?+
The receptacle install yes, the new circuit no. NEMA 14-50 requires a 240V/50A dedicated circuit from the panel to the garage with appropriate wire gauge (6 AWG copper). That circuit must be installed by a licensed electrician with an LADBS permit. Once the circuit and box are in place, handyman scope covers the receptacle install — $180–280 including device and finish trim.
Will new switches integrate with my HomeWorks QSX system?+
Hardware install yes, programming is a separate AV-programmer task. The pro will install the new switches, terminate to your existing low-voltage control wiring or wireless mesh, and coordinate scene programming with your Lutron certified programmer. Pure Caseta-only homes are simpler — programming through the Caseta app.
Can I get satin brass cover plates for every switch in the estate?+
Yes. Lutron, Leviton, and Hubbell all offer satin brass and other premium finishes on their commercial-grade lines. The pro will spec the finish across every device for visual consistency. Premium plate finishes add $15–35 per device over standard white.
What does multi-fixture estate visit cost?+
A typical Brentwood estate visit covers 8–15 devices across 4–6 rooms in a half-day to full-day window. Pricing runs $1,500–3,500 depending on device mix, finish requirements, and existing system integration. Estates with 25+ devices typically run across 2–3 days for clean execution.
Every outlets / switches pro verifies their identity
Government ID + selfie liveness check via Persona — required for every listing. Pros may earn additional Insurance Verified and License Verified badges by uploading documents we check. Read our standards →